Skip to main content

Circuit Diagram Temperature Sensor




 

Comments

  1. AnonymousOctober 29, 2025 at 11:06 PM

    Code link in description

    ReplyDelete
  2. AnonymousOctober 29, 2025 at 11:06 PM

    Code link in description

    ReplyDelete
  3. AnonymousDecember 29, 2025 at 4:47 AM

    // Define the pin where the LED is connected
    int BUTTONpin = 2;
    int LEDpin = 12;

    void setup() {
    pinMode(LEDpin, OUTPUT);
    pinMode(BUTTONpin, INPUT);
    }

    void loop() {
    if (digitalRead(BUTTONpin) == HIGH) {
    digitalWrite(LEDpin, HIGH);
    }
    else {
    digitalWrite(LEDpin, LOW);
    }
    }

    ReplyDelete
  4. AnonymousDecember 29, 2025 at 4:47 AM

    aw shucks

    ReplyDelete

Post a Comment

Popular posts from this blog

Solar Tracking System

Dual-Axis Solar Tracking System | Arduino SimpleCircuits Arduino Solar DIY Renewable Energy Project Dual-Axis Solar Tracking System Build a high-performance solar tracker that follows the sun in real-time. Four LDR sensors, an Arduino UNO, and two servo motors — boosting energy capture by up to 40% versus fixed mounts. 40% More Efficient 4 LDR Sensors 2 Servo Axes <300mA Power Draw Finished Build System Overview How the System Works The tracker reads the sky through four LDR sensors placed around the panel, computes intensity deltas, and drives two SG90 servos in a real-time closed loop — keeping the panel perpendicular to sunlight from sunrise to sunset. ...
21 comments
Read more

Arduino Code Car Parking System

 // Created by Simple Circuits  #include <Wire.h>  #include <LiquidCrystal_I2C.h> LiquidCrystal_I2C lcd(0x27,16,2);    #include <Servo.h>  Servo myservo; int IR1 = 2; int IR2 = 3; int Slot = 4;           //Total number of parking Slots int flag1 = 0; int flag2 = 0; void setup() {   Serial.begin(9600);      lcd.init(); //initialize the lcd     lcd.backlight(); //open the backlight     pinMode(IR1, INPUT); pinMode(IR2, INPUT);    myservo.attach(4); myservo.write(100); lcd.setCursor (0,0); lcd.print("     ARDUINO    "); lcd.setCursor (0,1); lcd.print(" PARKING SYSTEM "); delay (2000); lcd.clear();   } void loop(){  if(digitalRead (IR1) == LOW && flag1==0){ if(Slot>0){flag1=1; if(flag2==0){myservo.write(0); Slot = Slot-1;} }else{ lcd.setCursor (0,0); lcd.print("    SORRY :(    ");   lc...
30 comments
Read more

Arduino Code

 //define Pins #include <Servo.h> Servo servo; int trigPin = 11; int echoPin = 12; // defines variables long duration; int distance; void setup()  {   servo.attach(13);   servo.write(180);  delay(2000);    // Sets the trigPin as an Output pinMode(trigPin, OUTPUT); // Sets the echoPin as an Input  pinMode(echoPin, INPUT); } void loop()  { // Clears the trigPin digitalWrite(trigPin, LOW); delayMicroseconds(2); // Sets the trigPin on HIGH state for 10 micro seconds digitalWrite(trigPin, HIGH); delayMicroseconds(10); digitalWrite(trigPin, LOW); // Reads the echoPin, returns the sound wave travel time in microseconds duration = pulseIn(echoPin, HIGH); // Calculating the distance distance= duration*0.034/2; // Prints the distance on the Serial Monitor Serial.print("Distance: "); Serial.println(distance); if ( distance <= 25   ) // Change Distance according to Ultrasonic Sensor Placement  { servo.write(180); delay(3000); ...
26 comments
Read more